Skip to main content

How to Clean Vintage Gillette Safety Razors


Cleaning vintage safety razors down to the shine

Today we're going to show you how to clean vintage double edge razors. We'll use a Gillette "Fatboy" Adjustable safety razor, a Flare Tip, and a Super Speed as examples - and see what we can find underneath. We'll use all sort of methods to strip away the grime.

When you buy vintage Gillette double edge safety razors at flea markets or garage sales, they are often so coated with decades of grime, corrosion, soap scum, and lime, that you can't tell what you'll have when the razor is clean. It's always exciting to find what sort of treasure you have!

Classic Gillette double edge ("DE") safety razors were manufactured in the first part of the 20th Century. They were made in US, England, and Canada. These cleaning methods also work on single edge safety razors, and on non-Gillette DE razors.

[Photos by Valerie Proctor Davis]

Many of these instructions are for cleaning vintage steel and nickel-plated razors. Cleaning chemicals can damage plastic, painted, brass-plated, or precious metal-plated razors. See notes under various cleaning methods for details.

Tools for cleaning vintage safety razors

Tools for cleaning vintage safety razors

Tools for Cleaning Vintage Safety Razors

These are the basic tools we use to clean shaving razors. If the razor is only a little dirty, we go straight to the ultrasonic cleaner.

  • Ultrasonic cleaner
  • Glass jar (or Barbicide disinfector)
  • Blow dryer
  • Old toothbrush
  • Cotton swabs
  • Dropper
  • Toothpicks
  • Rubber or vinyl gloves
  • Metal tongs

Ultrasonic Jewelry Cleaner - Quiet and Gentle Cleaning

Our little GemOro Ultrasonic Cleaner has lasted well for almost a year. It sits conveniently at the back of the counter and holds several Gillette shavers at once. No matter how clean a razor looks going in, the water will be grey or brown with dirt when it's finished!
The only downside is that the timer only goes to 480 seconds, so you may need to start it over a few times.
We use tap water with dish detergent or vinegar, but you can also buy a concentrated cleaning solution.

Cleaning materials for safety razors

Cleaning materials for safety razors

Cleaning Materials for Vintage Safety Razors

We rarely use all these on one razor - just what's needed! There are notes on each step about what each chemical is appropriate for.

  • Oven cleaner or foaming bathroom cleaner
  • Hydrogen peroxide
  • Nevr-Dull or Brasso
  • Toothpaste
  • Barbicide or rubbing alcohol
  • Mineral oil

The Gillette Fatboy is so coated with greasy dirt that we're going to start out by scrubbing it with oven cleaner (you can also use foaming bathroom cleaner).

Note: Oven cleaner and foaming bathroom cleaner are both very strong, so we only use them on very dirty steel or nickel-plated razors. If the razor has a painted handle or tip, be sure to keep it covered as the chemicals will remove the paint. This will damage plastic or brass-plated razors.

  • Wear rubber or vinyl gloves, and open the windows
  • Put the razor in a metal bowl or sink
  • Spray the razor, using metal tongs to turn it
  • Let soak for 3 minutes, then scrub with a toothbrush. Get into the corners inside and underneath the head, and into the base of the handle.
  • Rinse thoroughly

The Flare Tip and Super Speed double edged razors have less build-up, so we're starting them with a hydrogen peroxide dip. You can do this in a glass jar (we're using a Barbicide disinfector, as it's easy to lift the razors in and out).

Pour enough peroxide to cover the razors, and lower them in. Let them sit for at least two hours - you'll see a bubbly foam on them. If it's thick, rinse it off and put the razors back in.

When you take the razors out, rinse them thoroughly.

Note: Hydrogen peroxide will lift the paint off of painted handles, like the Gillette red-tip and blue-tip, and some black handles. If you need to clean the head, make sure the handle is out of the peroxide. Peroxide may discolor brass-plated razors.

Scroll to Continue

Disinfect Your DE Razors - Classic Barbers' Dininfectant

The Barbicide Disinfectant Jar has a stainless steel basket to add and remove your razors from Barbicide disinfectant. We also use a Barbicide jar for Evapo-Rust, alcohol or hydrogen peroxide. It eliminates splashing, and keeps you from having to touch the liquid.

You can purchase Barbicide disinfectant to use with your jar.

Now that the grime is loosened, put the DE razors back in the sink and scrub with an old toothbrush and toothpaste. Use toothpicks to get dirt out of the grooves, and be sure to scrub inside the base of the handle.

Rinse thoroughly.

If you have a delicate razor - plastic, bakelite, or brass-finished - always skip the chemicals and go straight to the ultrasonic cleaner.

You can use either cleaning concentrate or water with a little dish detergent ( and perhaps a bit of vinegar if the razors have a whitish deposit that won't come off).

Put the razors in the water and set the timer to 30 minutes. If it won't go that high, you may need to reset it several times.

Even though the razors have been through a lot of scrubbing, when the ultrasonic cycle is over, the water is usually dark with removed dirt.

If you don't have an ultrasonic cleaner, you can boil the razors in water with dish detergent or vinegar.

Cleaning Precious Metals

Treat razors plated in precious metals--silver, gold, rhodium, platinum--like jewelry. Don't use harsh chemicals or rough scrubbing. Use jewelry cleaning solutions, cloths, and brushes to preserve the finish.

You can use a liquid metal polish, like Brasso, or Nevr-Dull, which comes in cotton wadding.

Apply polish to the razors - if using Nevr-Dull, buff with the wadding. Use cotton swabs to buff inside the head and underneath, getting into all the corners. You can use toothpicks to work wisps of wadding into small crevices.

Note: In spite of its name, Brasso can damage brass. Only use it on steel razors.

Evapo-Rust - Removes Rust from Razors

Nevr-Dull - Easy Metal Cleaner

Run the razors through the ultrasonic cleaner again for a few minutes - metal polish residue on a razor can sting your skin.

Soak them in a disinfectant, either Barbicide or rubbing alcohol.

Use a dropper to put a couple of drops of mineral oil into the end of the handle, and the hole on the inside, under the center bar. Open and close the razor several times, then wipe the excess off.

Use a blow dryer on lowest setting to dry the inside of the head and inside the handle, so it won't start rusting.

Here they are at last, cleaned down to the shine. These turned out not to be perfect razors - they all have blemishes and noticeable wear.

But they will make sturdy daily shavers, and were worth the effort!

© 2012 Valerie Proctor Davis

How do you clean your razors?

Valerie Proctor Davis (author) from Birmingham, Alabama on September 13, 2014:

@Brite-Ideas, Collectors will go to any length to shine up their finds!

Barbara Tremblay Cipak from Toronto, Canada on September 12, 2014:

Now that's a procedure! I can honestly say that my boys would buy new ones, but my husband is a bit of fuss-pot and would probably follow this process!

anonymous on August 19, 2013:

Thanks for your efforts here. I had never heard of Evaporust before...I'm going to try to find that locally.

Ellen Gregory from Connecticut, USA on November 17, 2012:

It looks like a lot of work, but they look really good when they are done.

srsddn lm on November 15, 2012:

I wish I could preserve mine and use the techniques of cleaning suggested by you. Lovely lens.

anonymous on November 13, 2012:

That is a very well done article. You might want to repost it on The Shave Den and The Shave Nook forums, where it will get much more visibility than on Squidoo.

Thanks you for that very useful information!

anonymous on November 11, 2012:

Good job Valerie. Very informative. I've learned that most of the time, the ugliest razor will clean up to be almost mint condition. Also, dirty ones are always cheap to buy because the sellers are disgusted by them.

Valerie Proctor Davis (author) from Birmingham, Alabama on November 11, 2012:

@EEWorkouts: Thanks, I'll have to try that!

EEWorkouts on November 07, 2012:

What about oxiclean? I got a heavily corroded strainer looking new with a good long soak. Great lens!

Valerie Proctor Davis (author) from Birmingham, Alabama on November 07, 2012:

@Scarlettohairy: Thank you! It was a long day, taking those pictures!

Peggy Hazelwood from Desert Southwest, U.S.A. on November 06, 2012:

Wow, that's quite a process, but the results are stellar! Great step by step instructions. The photos are great too!

Related Articles