Skip to main content

How to Make Your Own Indo-Balance-Board

  • Author:
  • Updated date:

What you will need

  • Tape measure, pencil, newspaper
  • 1x piece of plywood (80cm by 50cm)
  • Jigsaw - with wood cutting blade
  • Sandpaper
  • Wood glue OR a drill (and screws)
  • 1x pipe tube (9cm - 16cm in diameter)
  • Varnish + brush
  • Paint (if you want to decorate the board)

    Indoboard retail price: £95
    THIS home-made board cost: £20

See below for best (in my opinion) products available for making an Indo Board.

Picture 1.

Picture 1. Indo Board shape

Picture 1. Indo Board shape

Picture 2


Picture 3.


Step 1. Make an indo board pattern with the dimensions

Using a piece of newspaper draw the shape of the indo board onto the newspaper. Indo boards are 75cm in length and 45cm in width. To help you get the correct curve and shape, cut a rectangle with these dimensions, fold the rectangle into four, and draw a curve along the outside edge. Cut along this curve and you should have an even oval shape when you unfold the newspaper. Picture 1. Will give you an accurate measuring guide so you can get your oval shape similar to one displayed here.

Step 3. Use a Jigsaw or similar tool to cut the plywood

Cut around the Oval shape using the cutting device of your choice, such as a jigsaw. Don’t worry too much if it is not exact, as you can sand it down afterwards.

Once you have cut the the oval shape, sand down the edges with regular sandpaper. This can be done using sand paper manually – or by using an electronic sander.

Step 2. Trace your oval shape onto the Plywood.

Place your oval shape on the plywood, then trace the pattern in pencil onto the plywood. Place the oval on the edge (so that you don’t have to cut any extra – see picture 2 and 3).

Picture 4.


Picture 5.


Step 4. Add stoppers at each end

There are two ways to accomplish this:

Trace around each end of the board (Picture 4) onto another piece of plywood, 8cm in width, so that you end up with a semi-circle shape (Picture 5). Do this for both ends. Cut the traced shape with the jigsaw and using wood glue attach these strips to each end. Glue the pieces in place and wait for several hours for the glue to dry. Once the glue is dry, sand the edges so they are smooth.

Alternatively, you can drill four holes in each semicircle and drill screws in to keep the plywood in place. Again, sand the edges for a smooth finish.

The bottom of your board should look similar to the one in Picture 6.

Step 5 - Varnish and sand the Plywood for a professional finish

To finish off your Indo board and ensure longevity - varnish your Indo board.
Make sure to dust off any sawdust and also sand down your board once before you start varnishing.

For the first coat of varnish you can use any quick drying varnish. A good technique to use is to first apply the varnish horizontally and then varnish in long strokes length ways (see video). This will ensure the varnish is absorbed into the wood grain and that the coat is smooth and evenly spread. This also creates a professional finish on the wood. Varnish both sides of the Indo board and leave to dry.

When the varnish is dry, sand the whole Indo board once again (with fine grade sand paper), and apply another coat of varnish. This will make the board extra smooth. Repeat this process two or three times until satisfied with the finish.

If you wish to paint designs or logo's on your board (see step 7) - then varnishing will ensure that the paint does not bleed into the wood and create streaks and uneven edges to your art work.

Picture 6 - Underside of the Indo Board


Step 6 - Make a balancing roller

The pipe used in this example is a high density polyurethane pipe, 10inches in diameter, and ideally needs a relatively thick wall of at least 5mm.

Cut the pipe tubing to 46cm using a hacksaw.

You may use the pipe as it is - or add friction tape to it as well, this will ensure the pipe does not slide from under your board.

Alternatively you can buy the foam roller below, which will still be much cheaper than buying both the indoboard and foam roller together.

Scroll to Continue

Indo Board Design


Step 7 - Customising your Indo Board

You can customise your Indo Board with your very own logo or text. There are two main methods you can choose from when making a design:

  1. Paint: Using acrylic paint (make sure the board is varnished first or the paint will run)
  2. Using permanent marker (again - only use over a varnished board)

One final step if to then varnish over your design. If you have used paint, then you can use any good quality varnish. If you opted for the permanent marker method, it is advisable that you use spray varnish, as the permanent marker may streak with normal varnish.

The video below shows illustrates how you can design your board with both paint and permanent marker.

A timelapse of how you might want to design your indo board!

How to use your new Indo Balance Board


sid on November 25, 2015:

awesome post!

I only wander where the black cilinder is made of, and what de sizes are

SarahG on October 18, 2015:

In the process of making mine and looking good so far! How many times did you varnish it before painting on it?

Storm on September 17, 2015:

how wide are the stoppers?

Luno2012 (author) from United Kingdom on December 11, 2014:

Hi @Mitch - the Dimensions are 76cm x 45cm, the other numbers in the diagram are there to help you get the curve correct, but you could just Draw out a rough sketch and make sure the curves are symmetrical also.

@kontantinos V - the 10cm pipe did work quite well, although I guess it makes balancing a bit harder. You could also buy a wider pipe and try with that. Good Luck!

Konstantinos Valsamidis from London on November 28, 2014:

Very nice tutorial. I m starting my own Indo right now!

However isn't 10cm PVC pipe a little too narrow?

Mitch on March 07, 2014:

This is a great post! Could you clarify what all the dimensions are for the board? The numbers are a little difficult to make out in the picture. Thanks!

Wylie fgrl on March 16, 2013:


Saul hen on March 16, 2013:


Luno2012 (author) from United Kingdom on December 27, 2012:

Hi - the thickness is 18mm :)

If you have any more questions feel free to ask!

AA on December 09, 2012:

Hi What is the thickness of plywood sheet?

many thanks for the video and plans.

Luno2012 (author) from United Kingdom on January 16, 2012:

Thank you! Sorry to hear you are having ACL surgery! Best of luck with it. I am now 16 weeks post surgery and working hard with rehab. If you have any questions about it, feel free to ask!

Thenicknick from Melbourne, Australia on January 16, 2012:

im actually scheduled to have surgery for a Torn acl, this gives me something to make for rehab afterwards, really good article mate well done!

yeti22 on January 13, 2012:


Luno2012 (author) from United Kingdom on November 24, 2011:

Thanks Resolver!

AnnaStephens - I have added a new video at the bottom of this hub which demonstrates how one might use this board. Many thanks!

AnnaStephens on November 16, 2011:

Hi Luno, this is a really informative hub. I just have one problem: I've no idea what an indo board is! So I could definitely make one from your instructions, but I wouldn't then know what to do with it...


Resolver2009 from Bournemouth, UK / Oslo, Norway on November 15, 2011:

Really well done and thorough article! Can't wait to make my own indoboard..! :D

Related Articles