Wooden house on brick base
House brick base continues
Welcome to our article (38), house brick base continues
Dear readers, this article is the continuation of Building a brick base, where we were going to explain step by step how to build a house brick base, so that, anyone can follow how is done. They can also use what they have learned to build something else.
Anyhow, in our last article, we have started to describe how to build a brick base on a sloping building site, we had reached the stage, where the bricklayers had set-up and built the southern wall high enough to lay some brick reinforcement and the damp course. Now, to keep our descriptions simple and accurate, we must assume that they are leaving an opening for a door, then continue to build this wall as high as the first brick on the concrete foundation at the highest corner. They need to do that, so, they can check and make sure that all the walls are level and there is no mistake in the level of the brickwork. Anyhow, once the bricklayers have done that, it starts to be easier for everyone to work on this brick base, since the whole house dimensions have been set-up, and everything is level.
Now let me make it clear, to start a house base on a stepped foundation is not easy, and the bricklayers must be careful and make no mistakes, especially on a sloping site and stepped foundations, since the foundations may not be level, because of the extra difficulty that the concreter encounter when laying the foundations on a sloping site.
Anyhow, when building every tradesman must rely on their skills, they must make sure that what they are doing is the right thing to do, they cannot blame somebody else for their own mistakes, therefore, when they find a mistake from the previous tradesman, whether they are concreters or other trades, whenever possible they should try to fix whatever there is to fix themselves, when that cannot be done, their foreman can recall the previous tradesman to fix their mistakes, before they go ahead and make the mistake bigger and more costly to fix later.
That is why the bricklayer cannot trust blindly the concreters. Anyhow, the bricklayers that are building this brick base are doing the right thing. They have built the lower part of the brick base level and they have made the first full course of bricks all around the house base. Now they can relax a bit, as everything is in the right place at the right level and there is no pig in the brickwork, as the last course of bricks makes a full circle of the house and ends up level, so, there is no pig in the brickwork, now, let us explain what is a pig in the brickwork and how it can happen.
Explaining a pig in the brickwork
Let me explain how a pig in the brickwork can happen.
Here I need to say that this saying, can be a local saying that explains; the brickwork is set in a way like a spring coil, so it never ends.
Now let me explain how it can happen, and how the bricklayer can create a pig in the brickwork. This mistake can happen on a sloping site, like the sloping site we are working on now. It can happen when the brick-walls are not exactly level, and the bricklayer ties the line on the wrong course of bricks, when they start building the last wall.
Therefore, let us go back to build our brick base, and let us assume that the bricklayer that is setting the wall on the eastern side is having some difficulty in setting the wall exactly level, because the foundation is not level, so, the bricklayer believe that he can make the walls level, by making the bed joint thicker before he reaches ground level; therefore, he lets his northern corner be a couple of centimetre lower than his southern corner on the same course of bricks, you see this is a long wall and if you only use the spirit level, you can hardly see that it is not level, but with the proper level or water level it will show the difference.
At the same time, the bricklayer that is setting the western wall is having some difficulties too and for the same reason is starting his wall and letting his northern corner be a couple of centimetre higher that his southern corner on the same course of bricks, he also believes that he can set everything right by making very small joint before ground level is reached.
Now, there is a difference of four centimetres at the northern wall, this is a problem, you see, four centimetres is more than half a brick, therefore, the bricklayer can easily tie the line on the wrong course; this is how a pig in the brickwork is created.
To make sure that there is no pig in it, the bricklayer needs to make sure that the walls are started level from the start, and then run a full course all around the entire building. The brick course should be like a closed even ring, and make sure that the walls are level, this is the only way to avoid mistakes. So, it is better to spend extra time at the start and get it perfectly level. I hope I have explained it properly and clearly, how a pig in the brickwork can be created.
Low set house base in progress
Building the rest of the brick-base
Let us assume that everything has been set properly, so, all the brickwork around is level and at the right alignment. But to make sure, we double check everything again by running a type measure and seeing that it agrees with the plans measurement, this now is a very simple job, because everything is set in hard cement and everything is level, so, if there is any mistake in the measurements it will show up easily.
Having checked everything and found that everything is right, we can proceed to complete the brick base. Anyhow, we have built the lower part of the base one brick higher than the highest corner of the concrete foundations.
Since the whole base has been set, the best way is to build higher the northern wall, which is now the lowest wall, we want to build it at least to above ground level, so that the trances can be back filled and then it is easier for everybody to walk around the building site, this is an easier job now since everything is in the right place at the right level. So, we build this wall above ground level. Having built the northern wall above ground level, now we must choose which wall to build next. But at the same time, let us see what the bricklayer can use to speed up the brickwork, like the bricklayer’s profiles, these are devises that can be attached to the brick walls to help the bricklayers. So, let us explain the bricklayer’s profiles.
Bricklayer external corner profile
Talking about bricklayer's profiles
Bricklayers’ profiles are helpful, because it eliminates the process of building the corners first, it also helps to keep the gauge easily, since the gauge is marked on the profile. I have always had a profile with me when I was laying bricks. Some of these profiles can be bought, but if there are not readily available on the market, and there is a lot of brickwork that needs to be done, by using your own creativeness you can make one yourself, all that is needed is a straight edge marked with the gauge that you can fasten to the walls.
There are at least two types of profile that the bricklayers can use to speed up his work, the main one is used for external corners. This external corner profile needs to be supported both ways to be effective, so, if you haven’t got one and you cannot buy one, you need to configure a device that can be tighten both ways, when you are making your own profile. You have to plan it in such a way that you can grab a brick from the joint on one side and two bricks on the other side, so that a sort of triangle is made and balance can be kept.
The internal corner profile can be a lot easier to make, and here I wonder why people don’t use it, since it is easier to make. All what is needed is again a straight edge with a hole or a few holes drilled in it and a special made up bolt or two that are thinner than the brick’s joint; these special bolts need to be modified and instead of their normal bolt head they should have a short cross say 30 to 40 mm welded at one end, and at the other end treaded with a butterfly nut. All the bricklayer needs to do now is to leave a hole in the bed joint near the corner, or clear the joint with a plugging chisel, then he puts one of his bolts in the hole of his straight edge; now he can push the bolt in the joint until the modified bolt head reaches the other side of the brick, then he turns the whole bolt 90 degrees, so that the modified bolt head is now vertical, and then he can tighten the bolt with his butterfly nut and at the same time make sure that the profile is plumb and he can use this profile instead of building the corner with his spirit level.
To complete this brick base
What else needs to be done to complete the brick base?
Let us now assume, that because the ground is sloping the base of this house has been divided, in such a way that the lower end can be used for garage laundry and utility room. To achieve that they have dug up the ground level about half the length of the house, and then dug a foundation to support a retaining wall and pillars to support the house above, the rest of the ground under the house will be left the way it is for the time being, because it is too costly to dig it out.
Anyhow, let us complete this brick base, as we have said above the lower side is now a certain height where the windows openings should be started. The windows are going to be tied to the brickwork, so, they need to be put in the right place and braced while the walls are being built. The bricklayers need to be careful that the windows remain plumb and in the right place while he attaches the window ties to the window and builds the tie into the brickwork. Here I may have to point out that placing the windows on the walls at the right height and at the right place, it’s one of those jobs that in this part of the world there is no rule who has to do it, say if the bricklayer is paid a fixed price for the amount of bricks he has laid, when he is placing and fixing the window on the wall he might not be paid, therefore, nobody is willing to do it, but there is no set rule and not much money for doing it, therefore, everybody wants to pass the buck to the builder or other trade people.
Having said that, now let us assume that everything has been done according to trading practice and the windows have been built into the brickwork accordingly. But here I want to point out that we have not talked about the lower part of the brick base that is being built on the higher part of the land, so, what needs to be done there?
The lower part of the brick base is built together with the rest of the base, but because it is lower it can be just one single brick thick with engaged piers under the house. These engaged piers may have a double purpose, one is to strengthen the walls and they may be used to carry the weight of the house if this part of the house is going to be a brick veneer. In this part of the house because there are no windows the bricklayer needs to leave some air vents, so that a minimum of ventilation is achieved. All this is going to be done according to specifications, as there must be some local rules and they may not be the same everywhere.
What we have written in this article is approximately what happens when we bricklayers build a brick base on a sopping piece of ground. So, I hope that I have not left behind any important description that would have helped the readers.
Now that we have built our imaginary house brick base, we believe that we have said enough in this article. So, see you soon in our next article, building a veneer house.
See you soon.
Some building and other useful links
- DIY brickwork
Thinking of laying bricks yourself, then read this hub it could help. DIY brickwork; Getting ready to lay bricks; making sure that we start the brickwork level, and Laying bricks on a sloping site.
- DIY Retaining walls
We are going to show you several types of retaining walls and how to build them, some of them briefly and other step by step, so that you could be able to do it yourself, if you like.
- D.I.W. house repairs
Replacing an old set of timber stairs with concrete treads on hot dip galvanized steel stringers, including step by step procedure and what you need to know if you want to D.I.Y. to save money.
- Building a brick base
Building with bricks, let me show you how we bricklayers set up a brick base from scratch. Setting a brick base on a sloping site is not easy, so let me show you how it is done step by step.
- The castle of
The castle of Monteserico in Genzano the Lucania has a history of its own, even though there isn't a real history written, today we are trying to put together known events and show you some photos.
- House building in Brisbane
Let us talk about houses building, some reasons why there are different ways of building in the whole world; ands in this hub we are going to talk about; House building in Brisbane in the sixties; Brick bases under timber houses, and, Working as a br
- Australia affordable houses
Building houses to sell is usually good business, when they sell easily, but when they don't sell the builders should really watch what they are doing, because they may need to sell their houses at cost and sometime below cost. Therefore for the buye
- Farming today compared to the old way
We have achieved a lot in agriculture in the last hundred years; so, let us compare how hard it was to harvest wheat or any other cereals the old ways to today ways by using these wonderful machines.
- An old man life story
Let any old man do his life duty by Writing An Autobiography about his own life and what he has learned from it, so that humanity may learn from what he has learned during his life.
- Australian building industry
How we are building houses in any part of the world is a very interesting subject to know, as we all have to live in them, therefore if we know how they are built, then it becomes easier for us to maintain and fix them if necessary. Therefore it coul
- My life my struggles
This hub is being written to tell you part of my life journey, as we all know there are a lot of times when during our lives we have to struggle, so this hub is telling you about my life struggles.
© 2012 F-Menchise