Skip to main content

Woodworking Made Simple with Decking Offcuts

My aim with DIY projects around the home is to look for innovative space-saving ideas and save costs on materials by recycling.

Decking Ramps for Wheelbarrow

Decking Ramps for Wheelbarrow

Seven Useful and Simple DIY Projects with Decking offcuts

Do you find the idea of woodworking daunting, if so then perhaps these simple ideas with just a few basic tools and nothing but offcuts leftover from decking may help to give you some inspiration and confidence to try something similar.

In these seven simple to make woodworking projects below I've used decking but any bits of scrap wood or offcuts would do and with a bit of imagination be turned into something creative, artistic and functional.

Why Decking and What Tools You Need


One Step at a Time

The only tools and material you need for the simple woodworking projects are:-

  • Tape Measure
  • Square
  • Pencil
  • Saw (suitable hand saw e.g. tenon saw, crosscut or rip saw, or a suitable electric saw)
  • Screwdriver
  • Screws and Nails
  • Wood Glue
  • Wooden planking e.g. decking or floorboards etc.
  • Optionally a bradle and drill may also be handy

The reason I chose decking for these projects is because they were spare decking and offcuts (from a couple of decking projects), decking that most people would normally throw in the skip or burn; but with a bit of imagination they can be a valuable source material for many simple and easy to do projects other than decking.

The bonus of working with decking for simple woodworking projects is that it's easy to work with, durable, strong and weather resistant (softwood being pressure treated) so will last for years outside when exposed to the elements. I could just as easily have used floorboards for these projects except it wouldn't be pressure treated and therefore for outside projects would be prone to rot quickly.

The Seven Easy to Make Woodworking Projects Illustrated in This Article

Using Decking Offcuts

  1. Ramps
  2. Compost Bin
  3. BBQ Table Tops
  4. Recycle Bin
  5. Raised Bed Planters
  6. Greenhouse Shelving
  7. Cat Scratching Post

I hope these simple projects give confidence and stimulate ideas for others to follow and try. I'm sure with some thought there are other simple projects you can think of that would put odd bits of spare leftover decking to good use rather than just wasting it in the skip or on the bonfire.


For the Wheelbarrow

Steps and wheelbarrows don't mix, if you have raised elevations in your garden and decking where there are steps rather than slopes and you occasionally need to traverse them with the wheelbarrow then some form of temporary removable ramp can be invaluable. If it's a series of steps then a plank of wood with battens screwed to the back at regular intervals to match the spacing of the steps (lining up with the leading edge of each step) to act as a step grip and stop the board from slipping is the simplest safe solution. And as it would be a temporary structure that's only used occasional it's not going to be outside long enough to rot and could be made from old floorboards; and stored in your shed when not in use.

However, for this project I just needed a couple of simple removable ramps for wheelbarrow access to the decking around the side of the house to gain access with the wheelbarrow between the front and back gardens. And using a few bits of decking offcuts was ideal, very fitting for the job; and being so small can easily sit in one corner of my shed out of the way without taking up any real space.

Making these ramps is the simplest of all jobs that requires few tools and doesn't require any real woodworking skills; and they can be knocked up within the hour.

As can be seen from the image below all that's required for each ramp is:-

  1. Cut two identical right-angle triangles where the shortest side is equal to the height of the decking above the ground less the thickness of the wood you're using to make the ramp. To cut the two triangles in one go cut your wood to length and then cut it diagonally across from corner to corner. Alternatively, if you cut them individually you should use the first right-angle triangle you cut as a template to cut the second one.
  2. Cut two lengths of timber equal to the length of the longest side of your triangles.
  3. Cut a piece of timber that's less than the width of your ramp deducting twice the thickness of the timber you're using and any overhang you may want e.g. if using decking offcuts of 5 inches by 1 inch (125mm x 25mm) then the width of your ramp will be 10 inches (250mm). So the piece you want to cut is 7 inches (175mm); 10 inches less 3 inches e.g. double the thickness of the decking and allowing inch overhang either side.
  4. Cut this 7 inch (175mm) piece of timber in half lengthways to use as support battens at the back and underside near the front; as shown in the image below.
  5. Screw and glue the pieces together (or nail and glue) using the picture below as a guide; and once the glue is set your ramps are ready for use.

2. Corner Compost Bin

Front Slats for Garden Compost Bin

This may be the simplest of all the projects here, using decking offcuts as slats for the front of a garden compost bin.

If you have an odd corner in your garden that you would like to use for composting some of your garden waste then quite often all that's needed are a few slats in the front to create a triangular space behind which you can put your garden waste during the summer months and then the following spring you can lift the slats to reveal freshly made compost for your garden.

Making a compost bin of this type requires slats because as the compost builds up its weight presses against the front and if you used one piece of wood, such as a sheet of exterior plywood, you wouldn't be able to lift it out to gain access to your compost. Previously I did use exterior plywood, but I cut it into strips specifically so that I could remove one slat at a time, working from top to bottom, when accessing the compost. However, following a decking project I had some bits of decking leftover which when cut to length served the same purpose but aesthetically looked at lot better. And decking is ideal for this type of project because it's pressure treated and will last for years.

Scroll to Continue

In a corner construction like this all that's required to hold the slats in place are a couple of posts or battens (if fixing to a wall) on either side with a gap between the posts (or battens) slightly wider than the thickness of the wooden slats to act channel to slide the slats in. The width of the channels should be quite generous allowing up to an extra inch (12mm) leeway for expansion as the wood expands otherwise as the wood swells it may become lodged in the channels and difficult to shift when you come to remove the slats to gain access to your compost.

Once you've devised some channels either side just cut the required number of decking to the same length and place in the channels as illustrated in the picture below.

3. BBQ Table Top

Jazzed up Brick BBQ

This is a fun one, transforming your Brick BBQ side table top quickly and easily with just a few decking offcuts all cut to the same length and fixed together with a couple of battens on the underside.

No skills, and few tools, are required to make this, and it can be made in less than an hour. The side BBQ table in this example is a patio slab on bricks and support against the wall on the BBQ side with a couple of metal supports. To face it, and jazz it up, with a bit of decking just requires cutting the required number of decking to the same length, slightly bigger than the patio slab (or area you wish to cover) and screw a couple of battens on the underside at either end using a few screws and some glue; a final piece of decking can be screwed to the front as a facing. The two battens acts not only holds the whole lot together but they also act as legs so if you keep the decking table in place permanently it allows for ventilation and drainage underneath thus preventing rot; although the top demonstrated here is removable so you can if you wish remove it and store it in your shed when not in use, to keep it in pristine condition.

For the battens you could use a couple of bits of decking, either full width or as shown here cut lengthways into strips.

4. Recycle Bin Made Simply

Recycled Decking to Make a Recycle Bin

As is the case in most places these days we are required to recycle most household waste, with one of the main problems being storage e.g. lack of space in the kitchen for all the recycle bins; therefore when I decked out our side passageway I bought an extra length of decking to ensure I had enough leftover specifically to knock together a simple box and lid just outside the kitchen door where all the recycle bins could be housed, as shown in the picture below.

Lucky Fit

Originally when I built this recycle bin (in the early days of recycling) all the local council gave us was a brown bin for kitchen waste, which I didn't use because we compost our own waste, and a black box for paper and card; with everything else e.g. tins, plastics, glass etc. having to be separated and put out in separate plastic carrier bags for collection. Therefore for ease of operation I made the recycle bin big enough to house my own odd assortment of plastic containers I found in my shed, and just transferred the rubbish from the containers to plastic bags on collection day.

However, after running a series of trials the council eventually issued a green box everything except glass, paper and kitchen waste (the old black box being for glass and paper) and the brown bin for kitchen waste.

When I removed my assortment of containers and put the three bins side by side in the recycle bin I'd previously made it was a perfect fit; as if I'd designed my recycle bin specifically for the bins we are now using. If I had made my recycle bin just an inch smaller in any direction then the assortment of new recycle bins issued by the local council would not have fitted.

The Making of the Recycle Bin with Lid

Anyway, this is the most ambitious of all the woodworking projects here as it's a box, and boxes need to be square. However, as a recycle bin outside its not critical if it's a little off square and is a good project as a starter to practice making boxes from wood.

Again, Decking is an ideal material to use for a project like this because the wood has already been pressure treated so even though its soft wood it's not going to rot for many years to come; and decking being a softwood is easy to work with, it's strong, durable and with groves on both sides is decorative making the box aesthetic rather than an eyesore. And because its decking, when the lid is closed, it's strong enough to stand on and therefore also double up as a convenient seat.

The construction is simple enough; in this case just a front and one side with a top plate around the other side and the back, and a hinged lid. Normally you might expect a full box with front, back and two sides, but in this case I took advantage of the recycle bin resting against the boundary wall and on one side the 'gossip step'.

You might be asking yourself what a 'gossip step' is, well because the houses in the street are built on a slight slope each property is up to three feet (900mm) lower than the next going down the street, so the boundary wall (depicted in one of the photos below) also acts as a retaining wall, with a fence on top. Therefore (as we get on with our neighbours well) in order for us to speak with our neighbours over the garden fence I built the 'gossip steps' (as you may just make out in one of the photos below).

Getting back to the recycle bin, the front is simply four pieces of decking of equal lengths fixed together with a couple pieces of decking fixed on the inside, acting as battens, in the same way as the lid is made (see images below). Five shorter pieces are all cut to the same length for the sides, the top piece cut at an angle to create a slope for better water drainage. The backing top piece is firmly screwed to the boundary wall as is the top side panel fixed to the gossip step. The front and side panel are then fixed in place using a batten (a piece of pressure treated timber) in each corner to act as corner butt joints.

If you can make something like this in your garden then you are well on the way to tackling more ambitious DIY woodworking projects.

5. Raised Bed Planters

Making and Adapting Raised Beds with Decking

Making simple boxes for raised flower, vegetable beds, flower borders and patio planters with decking; the raised flower and vegetable beds and patio planters could be as simple as four sides butt jointed together with a few nails to make a rectangle or box, and raised flower border being no more than firmly screwing a few sturdy pegs to the inside of a longer piece of decking at regular intervals and knocking them deep into the ground to hold the decking firmly upright in position. Although if using decking for a flower border in this way I would recommend using thick timber for the pegs e.g. 2 inches (50mm) square minimum and that the pegs go at least 1 foot (30cm) into the ground.

I recently helped a friend to landscape his back garden for organic vegetable growing. Previously, apart from his impressive fish pond with filter bed and water feature he hadn't done much with his back garden other than cut the lawn, plant a few wild flowers and let the weeds rule between plants in his flower beds. This year, having seen the success in my garden in growing wholesome vegetables for healthy cooking and the money it saves on the shopping bill he was keen to follow suit and grow a few vegetables of his own. We started by making a small raised vegetable bed using brick blocks, then when shopping in Belgium and seeing a couple of wooden raised beds at a bargain price he caught the gardening bug and wanted to do more to grow his own vegetables. So with my help we tidied up his garden a bit and seated one of the wooden raised beds in a flower border at the end of his lawn where he could grow a selection of plants from the marrow family, including pumpkin, courgettes and marrows. The other raised bed he bought fancied having raised on legs on the lawn near his house so he wouldn't have to bend to attend to it and more importantly it would be near his kitchen so that he could just nip out and pick herbs and fresh vegetables as he was cooking.

This second wooden raised bed was quality made from pressure treated wood but as is normal with this type of bed it had no base, and of course no legs. Therefore he designed his own modifications which included adding an outer ring to the bed itself (using decking) giving small planting troughs for herbs around the outside, using decking for the base and standing it on pressure treated wood for the legs. His design left an area around the base that naturally leads itself to anther raised bed at ground level, so as shown in the photos, I suggested he completed the job by using some more decking to make an addition planter underneath.

Having completed this project he then went on and made another raised bed on legs to his own design, completely from scratch using decking for the bed and pressure treated timber for the legs.

6. Greenhouse Shelving

And Staging from Decking

Although I have aluminium staging in my greenhouse with removable aluminium shelving there is space at the back of the greenhouse for a shelf, which is always useful. Previously I used just ordinary wood for the shelf but overtime with the heat and humidity it naturally warped and needed replacing so this time I replaced it with a spare bit of decking offcut I had in my shed; later if I get a longer spare piece I’ll replace it with the longer piece. Any spare decking you may have laying around in your shed would also make great shelving in your garden shed or DIY workshop.

Although I already have staging in my greenhouse if you don’t then decking would certainly be an ideal material to make one; obviously well-spaced as slats to allow good drainage but the spaces between the slats shouldn’t be so big as to allow pots to sit properly with no danger of tilting down the cracks e.g. a one inch space between slats should be about right.

Shelving for greenhouse made from decking

Shelving for greenhouse made from decking

7. Cat Scratching Post

For Our Maine Coon Cats

When we had our kittens a couple of years ago, brother (Greebo) and sister (Dippy) we also bought a scratching post with platform for them; which they broke last year, simply because they are half-breed Maine Coon cats (their father being a Maine Coon) and the scratching post is designed for normal size cats.

Anyone who has Maine Coon cats will know they are large and heavy, so much so that we even had to replace the cat flap last year (when Greebo started to get stuck in it) with a small dog flap; and even now Greebo only just fits through it.

Anyway, rather than throw the broken scratching post away, there was nothing wrong with it except for the broken platform, I unbolted the old platform and replaced it with a couple bits of spare decking.

To hold the decking together and firmly secure to the post I screwed and glued two battens underneath the decking one each side of the post.

The cats love it, they love having their own bit of decking which they can sit on; and most evenings they sit on it to look out through the French doors onto the garden.

Maine Coon cats and their scratching post repaired with decking.

Maine Coon cats and their scratching post repaired with decking.

What People do With Their Wood Offcuts

This content is accurate and true to the best of the author’s knowledge and is not meant to substitute for formal and individualized advice from a qualified professional.

© 2012 Arthur Russ

Leave Your Crafty Views Here

Arthur Russ (author) from England on June 15, 2017:

Thanks for all your feedback and comments; all greatly appreciated.

Susie Lehto from Minnesota on October 10, 2014:

You do have a lot of creative ideas for decking cuteoffs.

I would love some of those raised garden beds for sure.

Thumbs-up on an interesting and useful hub. :)

diegocomercio on July 29, 2013:

nice interesting ideas

anonymous on November 16, 2012:

Grea lens with terrific wood decking ideas

DebMartin on October 25, 2012:


AnindaPramanik on October 13, 2012:

great work

WriterJanis2 on October 13, 2012:

So much great info and a very cute cat. Gotta bless this for your kitty. :-)

John Dyhouse from UK on October 12, 2012:

Great lens, if I hadn't already done so I would be running for the off-cuts now. Very useful anda informative. Blessed

Pet_club_India on October 12, 2012:

wonderful lens

Cris-ti on October 10, 2012:

Very nice lens.

Cris-ti on October 10, 2012:

Very nice lens.

ScottMckinzie on October 10, 2012:

Nice Lens! Reading through your lens is just great! However, it means I have a lot to learn lol...Great Job!!:)

anonymous on October 10, 2012:

I enjoy reading through your lens :) Keep working ,great job!

casquid on October 10, 2012:

Great lens! LOTD, wonderful!

anonymous on October 09, 2012:

I was just here Saturday and just now noticed home page honors, congratulations!

Gloria Freeman from Alabama USA on October 09, 2012:

Hi thanks for sharing these ideas, I like the flower boxes. This is a great reuse post, blessed and added to my lens...Squid Angel flinnie.

anonymous on October 07, 2012:

i like the ramp ideas thanks for sharing

fullofshoes on October 07, 2012:

Very well done. We love to "repurpose" materials and find creative ways of making the best use of space. Your ideas will definitely help us with some upcoming projects. ~blessed~

Karnel from Lower Mainland of BC on October 07, 2012:

I enjoyed reading this information well done!

anonymous on October 06, 2012:

Using decking offcuts for other projects just makes good sense and you don't have to buy new materials...and you have paid good money for those leftovers! Also, they just look nice. You certainly know how to make use of every inch of space, I especially like how you did your compost bin, I've never seen one that was so attractive before...nicely presented and I love how you tell the process along the way, well done!

Linda Jo Martin from Post Falls, Idaho, USA on October 05, 2012:

Thanks... your lens is very inspiring. I'm impressed that you found so many beautiful ways to use your decking.

Related Articles