Over the years I have been using various resins for casting objects for my business and for making objects for my home. I now only work with Jesmonite resin because it is less harmful to my health.
I did a few projects in polyester resin and epoxy resin but due to the lack of space and an adequate working environment I decided to avoid them. I generally work with Jesmonite for most of my simple projects,
I had some research to do for a project for a customer in the UK, I decided to practice making a cube made from composite materials to look like vintage steel, a rusty iron cube. the final project was to make a large panel of faux metal with a logo embossed into it for a Business office sign.
I ended up making a number of cubes in various finishes using different materials.
Mould Making and Casting Techniques
How I made A Faux Metal Cube
To make the cube I first cut a block out of 12" thick polystyrene from a larger sheet of 96" x 48"x12". Polystyrene sheeting is available in various thickness supplied by insulation and packaging companies. The polystyrene was cut using a hot wire. We have a large hot wire cutting table in the workshop which allows me to cut large blocks of polystyrene into various shapes.
The next stage of the process was to coat the polystyrene in a layer of silversand, silversand is a fine grain sand, i could also have used paving sand. the sand is air dried first over a number of days in the sun or under an air dryer.
To coat the polystyrene with the fine grade sand I coat the polystyrene with waterproof PVA, it must be water proof PVA or the process does not work properly. I coated on side at a time and then poured the dry sand onto the PVA and allowed it to cure, then do the next side and allow to cure. Once all sides were coated in a even layer of sand coating I made a nice cup of coffee and prepared the next stage.
The Jesmonite Stage
The next stage in the process was to make some water based resin using jesmonite. A mix of one part liquid AC100 and two parts filler powder works perfectly for me, maybe a bit more filler. ad the filler to the liquid not the liquid to the filler. I them mixed it with a domestic hand held blender until smooth.
The resin cured with in minutes so I had to apply the mix onto the sand coated surface of the block fairly quickly. One surface at a time and then allow to cure. Once i had coated one face I place a smooth sheet of silicon paper onto the surface and then a sheet of hardboard and allowed it to cure. When the resin had hardened after about twenty minutes i removed the silicon paper and the hardboard and then repeated the process again until all size sides were coated in jesmonite water bases resin.
The effect on the block was a series of flat and uneven areas on each plain with some rough sand textured sections which when painted would resemble rest.
Jesmonite is a brilliant material to work with, much easier to use than epoxy resin or polyester resin which are rather toxic to the user and to the environment.
Painting The Cube
To paint the cube I first painted a layer of vinyl matt emulsion diluted with water and colour mixed to my desired tonal finish. I painted all six sides in one go and allowed to dry in the sun.
The next later I used an old paint brush to cover the block in a silver coloured paint, Bedec silver satin paint and while the paint was still wet a put another layer of very dark brown paint applied by a rag cloth. Areas of paint were removed with a clean rag to allow the orange paint to show through in places. Speed is important because the Bedec paint cures quite quickly. the black was allowed to cure on a sheet of silicon paper. the silicon paper stops the paint from sticking to the surface it was siting on.
The paint cured and the result seemed to work quite well for the desired purpose. Working on a larger area like a panel was even harder due to the time constraints of curing times of materials.
Cast Jesmonite Cuboid Test Project
Cast Jesmonite Test Project 16th June 2015
In June 2015 we had a job to make some masonry cast stone letters for an architectural pub sign name for a Free House Pub in England. Our customer wished to have 3D letters made of materials that were to become part of the structure of the building. The letters were cast in stone with jesmonite as the binder.
The reason for the test to make a cubeoid 10cmx10cmx10cm in Jesmonite cast stone was to find out how much material would be required to make a cubeoid and then use this information to calculate how much jesmonite would be required to do my cast stone jesmonite pub name sign letters.
Test results. A cast jesmonite cubeoid 10cmx10cmx10cm weighted 2.1kg.
10x10x10=1000. 31.62 square root of 1000. 2100grams/1000=2.1grams. 1cmx1cmx1cm of cast jesmonite = 2.1grams. 1cmx1cmx2.5cm=5.25grams. A cast jesmonite letter 45cm high by 1cm thick uses 1350cmx1cmx1cm of jesmonite or 36.74x36.74x1cm. Letters required were 2.5cm thick therefore each letter used 36.74x36.74x2.5cm=1350cmx1cmx1cm of jesmonite,
1cmx1cmx1cm of jesmonite weighed 2.1grams. 1cmx1cmx2.5cm weighed 5.25grams. 5.25x1350=7087grams=7kg of jesmonite.
Each letter 45cm high by 2.5ch thick weighed 7kg.
12 letters were required for the job. 12 x7=84kg of jesmonite required for the job.
A mix of jesmonite we used was 1 part liquid to 2.5 parts powder. 84/3.5=24. We required 24kg of liquid and 60kg of powder.
The actual amount of material used in the end was less due to a third component being the ground stone particles which we used to replace some of the jesmonite, roughly 1/3 was ground kiln dried stone particles. We ended up with quite alot of spare jesmonite for another job, we just needed to have a rough idea of what amount of material needed ordering from our suppliers.
Cast Resin Iron Ornament Of Some Kind.
Cast Iron Resin Project Test
Cold cast iron resin project. Purpose of project to practice working with Jesmonite resin adding iron powder to the mix and allowing it to oxidize and become rusty when exposed to water.
The mould was made from hot wire cut HDFRA grade polystyrene. The cast resin mix consisted of 2 parts liquid ac100 jesmonite, 5 parts powder and 1 part kiln dried fine grade sand and finally 1 part iron powder. I poured the liquid into a suitable large 2litre plastic container, added the powder, mixed together with an electic drill fitted with a special blending extension. Dried sand was then added and mixed, iron powder was then finally blended together until a smooth mix was achieved. The mixed resin was then poured into the mould. trapped air was removed by agitating the mould on a vibration table. The resin was allowed to cure for one hour before removing from the mould, the mould was destroyed in the process. The cast resin object was then cleaned up using wet and dry sand paper and metal files and rasps.
The object was left out side and water was sprayed over the casting. 24 hours later rust appeared on the surface of the cast.
Conclusion. A higher amount of iron powder would be an option.
- Cast Resin Letters | Cast Resin Lettering and Cast Resin Numbers For Property Names
makers of cast resin letters and cast jesmonite stone letters
- A How to Website for Mould making and Casting in Resin
A website managed by a gentleman named Richard, the Technician of the mould-making and casting workshop at Nottingham Trent University. Welcome to Casting About’
- Jesmonite – Index
The manufacturer of jesmonite
- Bruce Gordon - Scupture
A link to a person who works with Jesmonite.
carlarmes (author) from Bournemouth, England on May 03, 2015:
Hello, thanks for visiting and don't forget to comment or promote your own hub while you are at it.